Pull the duplexer tray release-tab (callout 1) to release the duplexer tray magnets. Remove the left-side cover (see Left-side cover), the right-side cover (see Right-side cover), and the back cover (see Back cover). Reinstallation tip Make sure that the flag (callout 1) and both of the fuser-release levers (callout 2) fit through the holes in the cover before attaching the cover.ĭuplexer tray 1. Lift the cover straight up and away from the printer. Slide the cover toward the right side of the printer to clear the tab (callout 3) on the duplex tray. Release the tab (callout 2) at the back of the printer on the right side of the printer.ĥ. Tip the printer so that it rests on its front. Remove the left-side cover (see Left-side cover) and the right-side cover (see Right-side cover).
Lift the cover away from the printer.īack cover 1. Removing the right-side cover (2 of 2) 4. Use a flat blade screwdriver to pry the cover at the back of the printer, releasing two internal tabs (callout 2). Lift the back of the printer off of the workspace and use a flat blade screwdriver to pry the cover from the tab (callout 1) at the bottom of the printer.ģ. Slide the cover toward the front of the printer to clear the interlock tab (callout 2).
NOTEĪ screwdriver is required to remove the left-side cover from an HP LaserJet 1160 printer.ģ. Release two tabs (callout 1) to pry the cover away at the back of the printer approximately 38 mm (1.5 inches). Remove the main input tray (tray 2).īefore you proceed to step 4, examine the position of the separation pad in the tray. If the printer regularly pulls multiple sheets of media at a time, you might need to change the separation pad. The use of poor media might require more frequent replacement of the separation pad. Plug the power cord into the printer and then turn on the printer.Ĭhanging the printer separation pad Normal use with good media causes wear. Reinstall the print cartridge, and close the print-cartridge door.ġ7. Close the front automatic two-sided-printing path door.ġ6. Place the printer on the work surface with the top of the printer facing up.ġ5. Push the right tab to the left, and rotate the tab downward into position. Place the end cap over the shaft on the left side, push the end cap to the right, and rotate the tab downward into position.ġ3. Rotate the shaft until the notches engage and the shaft clicks into place. Insert the left side of the new pickup roller into the left slot (1), and insert the right side (with notches in the shaft) into the right slot (2).ġ1. Slide the pickup roller assembly to the right, and remove the left end cap.ġ0. Slide the right tab to the right, and leave the tab in this position throughout the procedure.Ĩ. Pull the white tabs outward, and rotate the tabs up.ħ. Place the printer on the work surface with the front of the printer facing up.Ħ.
#Hp laserjet p2055dn printer pdf series
Open the front automatic two-sided-printing path door (HP LaserJet 1320 Series printer only).ĥ. Open the print-cartridge door, and remove the print cartridge.Ĥ. Turn off the printer, unplug the power cord from the printer, and then allow the printer to cool.Ģ. CAUTIONįailure to complete this procedure might damage the printer. See Ordering parts and supplies to order a new pickup roller. If the printer regularly mispicks (no media feeds through), you might need to change or clean the pickup roller. The use of poor media might require more frequent replacement of the pickup roller. Step #4 – Replace the fuser.Ĭhanging the pickup roller Normal use with good media causes wear. Here is the outline of installation steps: Step #1 – Replace the pickup roller. Because of the advanced nature of this installation, we can only provide limited technical support for this kit.
If you have never done this before you will want to allow a couple hours for installation. HP LaserJet 1320 - Maintenance Kit Instructions Please note that installing this maintenance kit is considered an advanced installation procedure.
0 kommentar(er)
